Ford Focus Forum banner
1 - 14 of 14 Posts

·
Registered
Joined
·
10 Posts
Discussion Starter · #3 · (Edited)
Yes. Still for sale. I've been pretty occupied so my attention was away from selling this.

With in these 5 months, Had a small ding in the rear right quarter panel from NYC parking, nothing major.
The clutch master cylinder is starting to fail. Parts in hand, Installing Monday.

In my mind, I would like $4,000. I understand its high so ill use that as a baseline. Make an offer.
 

·
Registered
Joined
·
1 Posts
I am posting this to see what i can get for my unmodified 02 SVTF with 112,xxx Miles. Located in NYC. Bought with the intentions for a track car but plans changed and is currently being used as my daily. I just bought a house so i am looking to use the money for potential renovations/projects. I don't have to sell since insurance is super cheap and is great fun daily (way better mpg than my pickup) BUT i am willing to let it go for the right price.

Title is clean, clear, in my name ready to sign.

Condition:
Exterior: Small scratches and imperfections here and there due to age and NYC parking
Headlights starting to get foggy
Interior: Small hole in driver seat. Everything else is in great condition.

Mechanical: The car runs perfect with no lights, no issues.

New Parts(Motorcraft Ignition Coil
Plugs SP-463(gapped .60)
Wires
All filters (Fuel, Air, cabin)
Fluids (Motor and Trans)
Valve cover gasket
Motorcraft Knock sensor
Motorcraft Crankshaft Position sensor
Motorcraft 02 sensors
Rotors (Non slotted/ non drilled since its my daily) and Pads
Motor and trans mount
Front sway bar end links
thermostat housing
valve cover gaskets
Tires (Falken Ziex ZE950 A/S)
Drive side window regulator
(Timing belt done by previous owner. Did a visual inspection and belt looks new)


Will include (Uninstalled) :
4G Wires (For the Big 3 Upgrade)
Left and right control arms
Moog Ball joints
Thermal paste (for IMRC)
Copper Shift bushing (replaces the square rubber bushing)(might install soon)
Extra Motorcraft Oil and filter
Extra Motorcraft xtm5qs Trans fluid


Things inspected:
IMRC and DSI Clip
VCT Solenoid
Shift cables
Cleaned MAF, Throttle Body

currently at work. Will post more photos soon View attachment 7609



Sent from my iPhone using Tapatalk
 

·
Registered
Joined
·
10 Posts
Discussion Starter · #7 · (Edited)
I am currently in the process of Installing a new slave cylinder and while I am in there a new clutch and flywheel (LUK) (The old one seems to be in pretty good condition as well. It will be included with the car).

I should be done before Christmas. I only work on it when I have the time and all I have left is to install the entire transmission and and put everything else back on. Ill update as I go.
 

·
I
Joined
·
13,460 Posts
I am currently in the process of Installing a new slave cylinder and while I am in there a new clutch and flywheel (LUK) (The old one seems to be in pretty good condition as well. It will be included with the car).
Don't forget the sealant on the back of the slave cylinder if you use a LuK! This replaces the o-ring that you'll see on the OEM slave.
 

·
Registered
Joined
·
10 Posts
Discussion Starter · #9 · (Edited)
Don't forget the sealant on the back of the slave cylinder if you use a LuK! This replaces the o-ring that you'll see on the OEM slave.

Yep! Done. (thanks to all the info provided on this forum) Just mounted the Trans today. It was a pain in the @SS getting the clutch spline aligned and seated.. Hopefully ill put everything else back together by the end of the week.

I will also be replacing the thermostat housing with the contour one. I accidentally banged it with the bell housing and it started seeping coolant.
 

·
I
Joined
·
13,460 Posts
Yep! Done. (thanks to all the info provided on this forum) Just mounted the Trans today. It was a pain in the @SS getting the clutch spline aligned and seated.. Hopefully ill put everything else back together by the end of the week.

I will also be replacing the thermostat housing with the contour one. I accidentally banged it with the bell housing and it started seeping coolant.
Good deal, glad you got it. Doing the job alone (especially getting the transmission back in) is a pain.
 

·
Registered
Joined
·
10 Posts
Discussion Starter · #12 · (Edited)
BUMP!
Car is back on the road!. New Clutch, flywheel, master and slave cylinder!. Recent alignment and inspection. I just replaced the roof of my house and getting rid of most of my side projects to fund it. Looking to sell soon! Send me your offers.
 
1 - 14 of 14 Posts
Top