Ford Focus Forum banner

1 - 20 of 30 Posts

·
Registered
Joined
·
397 Posts
Re: Dyno is in but.......

what where your numbers?
 

·
Registered
Joined
·
4,271 Posts
Re: Dyno is in but.......

Yes numbers, rpm, type of turbo, cooling......DETAILS
 

·
Registered
Joined
·
197 Posts
Discussion Starter #4
Re: Dyno is in but.......

One vid is of a base line of my SVT (cold air,camgear,alt pully,plugwires,JET performance module,and cat back) 171whp at 6300 rpm

the second vid is with a 70 shot from NX wet kit and pulled 233whp

I only got 62hp out of the 70 shot but still good I think
 

·
Registered
Joined
·
1,198 Posts
Re: Dyno is in but.......

you get 171whp, NA?..

Do you have teh dyno to backup those numbers?
 

·
Registered
Joined
·
2,375 Posts
Re: Dyno is in but.......

Does the "SAE 1.16" mean it's corrected for 16% drivetrain losses, or am I confused?

I see it was a mobile dyno type setup...since it's not there, can we assume they didn't log your air/fuel ratio? Also, is that cam gear tuned or just at 0°?
 

·
Registered
Joined
·
12,749 Posts
Re: Dyno is in but.......

Do you have an ORP??? 171 is just unreal for a CAI, Cam Gear and Wires. If those are the only mods you have, then I'm guessing it's a relatively juiced dyno, coupled with a nice factory car!! Either way.. congrats!
 

·
I change diapers now
Joined
·
14,444 Posts

·
Registered
Joined
·
19,264 Posts
Re: Dyno is in but.......

I'm callin BS on a baseline of 171whp for a lightly modified SVT.... those listed mods don't give 20hp....
 

·
Registered
Joined
·
12,749 Posts
Re: Dyno is in but.......

Well can't call BS. Either he's fibbing on the mods, or that dyno is off by at least 10 more likely 15whp! But I dunno.. arguing dyno's seems hardly worth it
 

·
Registered
Joined
·
404 Posts
Re: Dyno is in but.......

Correction of 1.16?? I've never seen a factor that high.
A stock SVT will average around 147 whp. With that correction it brings it to 170.5.
If they are using the old DynoJet DOS software, you can alter values to change HP readings.
 

·
Registered
Joined
·
19,264 Posts
Re: Dyno is in but.......

Well OK I'm calling "something ain't lining up in the cosmos" instead of BS.
 

·
Registered
Joined
·
5,141 Posts
Re: Dyno is in but.......

Well OK I'm calling "something ain't lining up in the cosmos" instead of BS.
 

·
Registered
Joined
·
197 Posts
Discussion Starter #19
Re: Dyno is in but.......

Or we can run them at the track. OR you can produce the dyno and pay for It and you can watch in person. yall can believe it or not but I proved it with the dyno sheets and I am willing to let yall watch the vids its not like it was my buddies dyno this was done at NOPI Memphis and like I said all I have is

AEM Cold Air Intake
AEM CAm Gear (advanced 4 degrees not retarded like everyone says)
AEM Alternator pulley
Taylor Plug wires
Catback Flowmaster Exhaust
Jet-peformance Module
and 70 shot from NX
 

·
I change diapers now
Joined
·
14,444 Posts
Re: Dyno is in but.......

Nobody said you didn't make the numbers posted.

We're just noticing that the corection factor is very high.

- Drew
 
1 - 20 of 30 Posts
Top