Average E/T for an SPI 5-speed?

bryan_ruiz · Apr 15, 2004

I run constant high 16's with intake, exhaust, and underdrive pulley

donsbad68 · Apr 15, 2004

what size belt do u use with ur pulley and which pulley is it?

steble01 · Apr 15, 2004

You can expect slightly better acceleration and quicker engine response/reving with one of these.
Also, you will need to change your accesory belt to a 1" shorter one. Here is a quote from the man behind BDR about it.. "We have noticed that Ford changed belts some time between the 2000 and 2001 models. We are not positive if this change occured mid-year or if it is a model year change. We have done installs on both years and it seems to be that a 2000' uses a 695K6 and a 2001 uses a 670K6.

Thanks,
Kevin
Black Diamond Racing
805.583.8255"

right from the SPI Aftermarket Parts & Mods List on the top of this forum.

00silverlx · Apr 15, 2004

best time without nitrous was a 16.7 but when i ran a 16.2 that was on about half a bottle so i may hit 16 or 16.1 with proper pressure though. that was with full interior and stereo in the car

donsbad68 · Apr 16, 2004

easy steble dont blow a gasket

steble01 · Apr 16, 2004

no im not blowing a gasket at all. but alot of questions that have been asked here recently (and just not yours) ae covered in the SPI Aftremarket Parts & Mods List. dont get me wrong, i definately dont mind helpin a brother out. that is all.

Gigaherz · Apr 16, 2004

the fastest et I've seen from an spi was I think a 14.8 and that was txfo who had headwork and nos.

EsCoRtLvR · Apr 18, 2004

Boy, that's not a hard goal to break

no offense to anyone.

While I'm building my other motor I'm putting all the bolt ons I'm using on that other motor on my current one until I'm done. I bet I could get near that N/A in about 6month time or so

Just need to shed about 50-75 lbs off the car and add about 40 horsepower and That'll do it.

donsbad68 · Apr 19, 2004

whats that 14's?

Jimmy · Apr 19, 2004

Ok, now what IS our redline?

I'm *planning* on going to the track and getting a dyno. Mine's stock except for a Giggy TB and an el crapo CAI from ebay.

Gigaherz · Apr 19, 2004

I think it's 5700 if my poor memory serves me right.

00silverlx · Apr 19, 2004

i just ran at the track with a full bottle and the back seat out and the stereo out. my best time was a 15.46 @ 91.7mph. i ran another time but only hit a 15.8 and a 16.0 had a bad launch the third time. i belive the synchros in my trans are going out it pops out of gear sometimes.

tin_maddog · Apr 21, 2004

Hey guys, I was wondering if you guys can tell me where you are launching. I either get bog, wheel spin, or bog then wheel spin and can't seem to find a nice middle-ground.

I just can't seem to make this bitch take off right.

goosesfocus · Apr 21, 2004

between 3000 and 3500

EsCoRtLvR · Apr 21, 2004

I run 195/60/15's I can't launch any higher than 1500 RPM without spinning like a siv. I get a 2.3 60ft launching at that RPM with the SPI controller

JeffescortLX · Apr 21, 2004

i just ran at the track with a full bottle and the back seat out and the stereo out. my best time was a 15.46 @ 91.7mph. i ran another time but only hit a 15.8 and a 16.0 had a bad launch the third time. i belive the synchros in my trans are going out it pops out of gear sometimes.

What size shot?

TXFO · Apr 21, 2004

screw the motor we need 14's

14.64 @ 99mph

35 shot plus everything you can think of and then some. Judging by the trap speed, better tires should lower the time but I can think of better ways to spend the money than on a mid 14 second focus.

Average E/T for an SPI 5-speed?

bryan_ruiz

donsbad68

steble01

00silverlx

donsbad68

steble01

Gigaherz

EsCoRtLvR

donsbad68

Jimmy

Gigaherz

00silverlx

tin_maddog

goosesfocus

EsCoRtLvR

JeffescortLX

TXFO

Top Contributors this Month

Recommended Communities